Bissell CleanView II Vacuum Cleaner Manual

The Bissell CleanView II is a powerful vacuum cleaner designed for effective cleaning of carpets and hard floors. It features a multi-cyclonic system that provides strong suction, a lightweight design for easy maneuverability, and a variety of attachments for versatile cleaning. Below are key sections for safety, features, maintenance, operation, and troubleshooting.

1. Features at a Glance 2. Maintenance 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Accessories 7. Using the Vacuum Cleaner 8. Accessibility Features 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Multi-cyclonic suction, washable filter, lightweight design, various cleaning attachments.

Feature	Description
Multi-Cyclonic System	Provides powerful suction for deep cleaning.
Washable Filter	Reusable filter that can be cleaned easily.
Lightweight Design	Easy to carry and maneuver around the house.
Attachments	Includes crevice tool, dusting brush, and upholstery tool.
Easy Empty Dirt Tank	Convenient dirt disposal without mess.

Maintenance

Regular maintenance is essential for optimal performance. Clean the filter and empty the dirt tank after each use.

Remove and clean the filter: Rinse under water and let dry completely.
Empty the dirt tank: Press the release button and dispose of the contents.
Check for blockages: Inspect hoses and attachments for clogs.
Inspect brushes: Ensure they are free of hair and debris.

WARNING! Always unplug the vacuum before performing maintenance.

First-Time Setup

Assemble the vacuum cleaner according to the instructions provided in the manual.

Attach the handle: Align and secure it to the body of the vacuum.
Install the filter: Ensure it is properly seated in the filter compartment.
Connect the hose: Attach the hose to the designated port.
Plug into an outlet: Ensure the power switch is off before plugging in.

CAUTION! Ensure all parts are securely attached before use.

Specifications

Power: 12 Amps.
Weight: 15 lbs.
Filtration: Multi-cyclonic filtration system.
Cord Length: 25 feet.
Cleaning Path Width: 13.5 inches.
Attachments: Crevice tool, dusting brush, upholstery tool.
Warranty: 2 years limited warranty.

Controls and Settings

Power switch located on the handle. Adjust suction power using the dial located on the front of the vacuum.

Attachments: Easily switch between attachments by pressing the release button.

Connecting Accessories

Ensure the vacuum is off before connecting or disconnecting accessories.

Align the accessory with the port.
Push until it clicks into place.
To remove, press the release button and pull the accessory out.

Tip: Use the appropriate attachment for the surface being cleaned.

Using the Vacuum Cleaner

For optimal cleaning, follow these steps:

Turn on the vacuum using the power switch.
Adjust the suction power if necessary.
Move the vacuum back and forth slowly for effective dirt pickup.
Use attachments for corners and upholstery as needed.

WARNING! Do not vacuum wet surfaces or liquids.

Accessibility Features

The Bissell CleanView II is designed for ease of use, featuring lightweight construction and easy-to-reach controls.

Care & Cleaning

Unplug the vacuum before cleaning. Wipe the exterior with a damp cloth; do not use harsh chemicals.

CAUTION! Avoid getting water in the motor or electrical components.

Regulatory Information

This vacuum cleaner complies with all applicable safety standards. For support, visit www.bissell.com or contact customer service.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Vacuum won't turn on	Power cord issue	Check power outlet and cord for damage.
No suction	Clogged hose/filter	Inspect and clear any blockages.
Brush not spinning	Jam or motor issue	Check for obstructions and reset the motor.
Excessive noise	Loose parts	Inspect for loose components and tighten as needed.

Reset: Refer to the manual for reset instructions if available.

Service: For assistance, contact Bissell customer service.