Bissell CrossWave 1713 SERIES Vacuum Cleaner manual

The Bissell CrossWave 1713 SERIES is a versatile vacuum cleaner designed for cleaning both wet and dry messes. It features a multi-surface cleaning capability, allowing you to clean sealed hard floors and area rugs with ease. The machine is equipped with a dual-action brush roll that picks up debris while simultaneously washing your floors. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Using the Vacuum Cleaner 8. Maintenance 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Multi-surface cleaning, dual-action brush roll, easy-to-empty tank, and a user-friendly control panel.

Feature	Description
Multi-surface cleaning	Cleans both hard floors and area rugs
Dual-action brush roll	Picks up debris while washing floors
Easy-to-empty tank	Conveniently dispose of dirty water
User-friendly control panel	Simple controls for operation
Lightweight design	Easy to maneuver around the house
Washable filter	Reusable filter for easy maintenance

Installation

Unpack the vacuum cleaner and inspect for any damage. Ensure all components are included.

Attach the handle to the base by aligning the slots and pushing down until it clicks.
Fill the clean water tank with water and the appropriate formula.
Plug the vacuum cleaner into a power outlet.

WARNING! Ensure the vacuum is unplugged when assembling or disassembling.

First-Time Setup

Power on the vacuum cleaner and familiarize yourself with the controls.

Fill the clean water tank with the recommended solution.
Adjust the cleaning mode based on the surface type.
Test the vacuum on a small area to ensure proper operation.

CAUTION! Do not use on surfaces not recommended by the manufacturer.

Specifications

Model: Bissell CrossWave 1713 SERIES.
Weight: Approximately 11 lbs.
Power: 4.4 Amps.
Tank Capacity: 28 oz. clean water tank.
Cleaning Path Width: 12 inches.
Surface Types: Hard floors and area rugs.
Filtration: Washable filter.
Power Cord Length: 25 feet.

Controls and Settings

Access the controls on the handle for easy operation. The control panel includes buttons for power, cleaning mode selection, and solution dispensing.

Cleaning Modes: Hard floor mode and area rug mode.

Adjust settings based on the type of surface you are cleaning for optimal results.

Connecting Devices

This vacuum cleaner does not require any external connections. Ensure the power cord is plugged into a standard outlet.

Using the Vacuum Cleaner

To use the vacuum cleaner, follow these steps:

Power on the vacuum cleaner.
Adjust the cleaning mode as needed.
Press the solution button to dispense cleaning solution while vacuuming.
Move the vacuum back and forth to clean the surface.

WARNING! Do not use the vacuum on wet surfaces that are not designed for cleaning.

Maintenance

Regular maintenance is essential for optimal performance.

Empty the dirty water tank after each use.
Clean the brush roll and remove any hair or debris.
Wash the filter regularly to maintain suction power.

Care & Cleaning

Unplug the vacuum cleaner before cleaning. Use a damp cloth to wipe the exterior. Avoid using harsh chemicals.

CAUTION! Do not immerse the vacuum cleaner in water.

Regulatory Information

This vacuum cleaner complies with all applicable safety standards. For support, visit www.bissell.com or contact customer service.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Vacuum not turning on	Power cord issue	Check power outlet and cord connections.
No suction	Clogged filter or tank	Empty the tank and clean the filter.
Brush roll not spinning	Debris blockage	Remove any hair or debris from the brush roll.
Water leaking	Tank not secured	Ensure the clean water tank is properly attached.

Reset: If issues persist, refer to the troubleshooting section in the manual.

Service: For assistance, contact Bissell customer service.